Factory supply · Export support · Global deliverysales@xiaoranmachinery.cn
Home / Products / Aerial Work Platforms / HC0607EA
SAFE ACCESS

HC0607EA

Crawler self-leveling aerial work platform with zero-turn steering, strong gradeability and long battery endurance.

Maximum Working Height7.9 m
Maximum Platform Height5.9 m
Request a QuoteWhatsApp us about this modelCompare Models

Technical Parameters

Standard configuration shown. Final specifications can be matched to working conditions, optional equipment and destination requirements.

Maximum Working Height7.9 m
Maximum Platform Height5.9 m
Rated Load250 kg
Platform Length1.67 m
Platform Width0.74 m
Platform Extension0.90 m
Extension Deck Load113 kg
Maximum Occupants, Indoor / Outdoor2 / 1
Overall Height, Rails Up2.39 m
Overall Height, Rails Folded2.06 m
Overall Length with Ladder2.02 m
Overall Width1.47 m / 1.30 m
Minimum Ground Clearance80 mm
Travel Speed, Stowed2.4 km/h
Minimum Turning RadiusZero turning
Up / Down Time16 s / 34 s
Gradeability40%
Maximum Working Angle, Lateral / LongitudinalX (20° / -16°), Y (14° / -14°)
DriveCrawler rear drive
Track250 mm × 72 mm × 60
Battery8 × 12 V / 160 Ah
Charger100–240 VAC / 13.5 A
Machine Weight1,890 kg
Standard FunctionsAutomatic braking · Single-side extension platform · Foldable guardrails · Self-locking platform gate · Charging protection · Proportional control · Emergency lowering · Motion buzzer · GPS · Emergency stop · Tilt protection · Load sensing · Fault diagnosis

Factory Supply

Direct equipment selection and configuration support from XIAORAN MACHINERY.

Project Matching

Model recommendations based on target depth, terrain, working height or lifting requirement.

Export Support

Documentation, loading coordination and spare-parts support for international delivery.

Match the HC0607EA to your worksite

This model lists 7.9 m working height and 5.9 m platform height, with 250 kg rated load. Working height includes an allowance above the platform and is different from platform height. Review ground conditions, access width, occupants and equipment weight before choosing a wheeled or tracked chassis.

Read equipment selection guides →   Discuss this configuration →

HC0607EA Selection & Buying Questions

Use these answers with the published specifications to check the site, configuration and delivery requirements. Confirm the final figures against the agreed configuration, drawings and supplied manual.

Based on this page’s specification table · Updated October 4, 2026

What are the HC0607EA working height and platform height?

The published maximum working height is 7.9 m, and maximum platform height is 5.9 m. Platform height describes the platform floor; working height includes an allowance for the person working above it. If the task requires the platform floor at a specific elevation, select by platform height and verify the actual work position.

How much weight can the platform carry?

The listed platform rating is 250 kg. Count occupants, tools and materials together. The extension deck has a separate 113 kg limit; this is not an extra allowance added to the platform rating. Follow the supplied manual for occupant numbers, load distribution and extension use.

Which dimensions should be checked before delivery?

Listed overall length with ladder is 2.02 m; width is listed as 1.47 m / 1.30 m; height with rails folded is 2.06 m. Ask which width applies to the ordered setup and request its dimensional drawing. Check doorways, floor capacity and the complete access route.

Is gradeability the same as an allowed working slope?

The HC0607EA lists 40% gradeability and separate lateral/longitudinal working-angle figures. Gradeability is not a raised-platform slope limit. Confirm the allowed levelling mode, ground support and operating envelope in the supplied manual before selecting a work location.

Can a spider crane replace this aerial work platform?

Do not assume interchangeability because a crane has an optional basket. Material handling and personnel access have different selection requirements. Verify the complete configuration, manufacturer-approved use and local requirements. State whether the task is moving material, positioning workers for installation or maintenance, or both.

Match the machine to your job

Send the task, required load or height, access dimensions, site photos and destination country for a model and configuration quotation.

Ask about this model